Until now, once the multi-currency feature was turned on in QuickBooks, it was impossible to revert back to a single currency. 'Now they have a way to undo this change and convert to QuickBooks Online'. 'Most users simply turned on the multi-currency feature without even using it' stated CIO John Rocha of QuickbooksRepairPro.com. E-Tech guarantees no loss of data and also offers a full money back guarantee. So far, hundreds of users have taken advantage of this service to move to the Online version of QuickBooks. Quickbooks multiple currencies feature. Remove seat and disconnect battery. Remove fuel tank along with both left and right side battery covers, and remove air box from carburetor (all per Yamaha standard shop manual procedures). Remove chrome plastic cover over fuel pump and disconnect choke cable/knob from lower pump bracket. Remove pump-to-carb fuel line from fuel pump. Upon closer inspection it was found that the Mikuni fuel pump had been mounted directly to the engine block below the carburetor, where two threaded holes that are just the right distance apart to mount the pump are located. What happens is the heat from the engine is transfer to the fuel pump causing vapor lock, the pump fails, thus not. Fuel Pumps: Specifications and Rebuild Kits Print version (pdf file). Mikuni makes a wide variety of fuel pumps for various engine and vehicle manufacturers. A few of these pumps, six in fact, are available as after market items through Mikuni American. Disconnect fuel pumps electrical lead connector. Remove two (2) hex-head pump mounting bracket bolts and remove pump assembly from motorcycle. Slide fuel pump up and off bracket mounting posts (Caution: excess fuel may drain from pump and/or fuel lines and fuel filter!). Remove heat shield. Remove remaining fuel line from pump. Pull all fuel lines from filter and remove steel springs and hose clamps from these lines (these will be reused on the kits fuel lines). With a sharp knife or box cutter, trim off the top portion of the fuel pumps rubber isolation/mount system per Photo A. Next cut pumps wiring harness approximately half way between connector and pump. Strip the insulation from the ends of these wires as well as from the supplied Baron harness extension wires. Using the supplied electrical butt connectors, crimp Baron harness extensions red wire to pumps black-w/blue-strip wire, and Baron harness extensions black wire to pumps black wire. Repeat this process on other side of wire harness extension with pumps connector. Now, referring to Photo B, you will need to cut off the square tube that runs along the side of the fuel pump with a hack saw. Cut down toward pump body in a straight cut, then cut tube off by cutting along the body. This will allow you to twist pump in the rubber mount so the curved spigot is facing up (clockwise approx 1/4 turn). Remove pump-to-carb fuel line from carb and separate electrical wires from this line. Remove this fuel line from engine. Re-route choke cable to right side of engine (toward carb) and rotate it up and over rear cylinder head back toward left side of bike. Mount new Baron choke bracket to the choke cable and tighten plastic nut. Vchannel app for mac. Studio Album (4) - Compilation (1) All Around the World. Jason donovan descargar mp3 Escucha la mejor musica en linea, Descarga miles de mp3 Gratis, MusicaQ es Musica de Calidad: Canciones de Jason Donovan Kylie Minogue feat. Jason donovan mp3. New choke bracket will mount to rear fuel tank mounting location (Photo C). 99~03 models – Remove electrical relay bracket (found under the right side cover) from the bike and slide each relay off of this bracket. Install fuel pump onto new Baron Fuel Pump Bracket and install bracket in the same location as the stock bracket you just removed, using stock mounting hardware. Refer to Photo F for proper installation. ![]() 04~07 models Remove electrical relays from stock bracket and remove relays from rubber holder. Cut rubber holder per Photo E and replace one of the relays into the rubber and install on to new Baron bracket. The second relay will be placed to the right of the tool bag under the seat and secured with the provided two-sided tape pad. Reconnect plugs to the relays.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |